PIK-20D list of drawings

Drawings with an active link may be downloaded from this page as pdf files. Observe that the drawing opening from the link is not necessarily the same amendment as that marked in the list. This due to the fact that the amendment that has been noted in the list may not be found in Trafi’s archives. In this case the drawing has been replaced by its closest equivalent. Drawings that are not listed may be ordered fromTraficom.

Size	Type	Chapter	Drawing	P/n	Subject	Amendments			Add. information
						a	b	c
Control system General
0	20D	20	001		Control system levers in center fuselage	04
0	20D	20	001	1	Lever attachment	04	50
3	20D	20	001	2	Aileron bellcrank	04	20
3	20D	20	001	4	Aileron control lever	04
3	20D	20	001	5	Wing flap control lever	04	20
3	20D	20	001	6	Aileron control lever	10
3	20D	20	001	7, 8, 14	Movement rods	20
4	20D	20	001	7-1	Pushrod head
3	20D	20	001	9	Airbrake bellcrank	04	20
4	20D	20	001	11	Airbrake shaft
4	20D	20	001	12	Airbrake control bracket	04	20
3	20D	20	001	13	Airbrake conrol arm	04	20
4	20D	20	001	15	Bush	04	20
4	20D	20	001	16	Washer	20
4	20D	20	001	18	Bush	20
4	20D	20	001	19	Washer	20
4	20D	20	001	31	Wing flaps control lever	20
3	20D	20	001	33	Wing flaps torsion tube	04	20
4	20D	20	001	33-2	Shaft	20
4	20D	20	001	37	Bush	20
4	20D	20	001	38	Bush	20
4	20D	20	003		Pushrod head	04
4	20D	20	004		Pushrod head	04
4	20D	20	005		Breakaway joint	04
3	20D	20	006-7-8		Plastic components
4	20D	20	009		Rod head	04
Aileron control system
0	20D	20	100		Aileron control system
4	20D	20	100	1	Pushrod 1
4	20D	20	100	2	Aileron bellcrank	20
4	20D	20	100	3	Pushrod 2
4	20D	20	100	4	Pushrod 3
4	20D	20	100	5	Pushrod 4
3	20D	20	100	6	Aileron bellcrank	04	20	40
3	20D	20	100	6-1	Aileron bellcrank	04	20
3	20D	20	100	7	Pushrods 5, 7 and 9
4	20D	20	100	8	Pushrod 6
4	20D	20	100	11	Pushrod 8
Rudder system
1	20D	20	200		Rudder system
1	20D	20	200	1	Rudder control
3	20D	20	200	1-2	Pedal	20
4	20D	20	200	1-3	Upper sliding tube	20
4	20D	20	200	1-4	Lower sliding tube	20
4	20D	20	200	1-5	Aft end piece	20
3	20D	20	200	1-6	Rudder control body	20
4	20D	20	200	1-7	Rudder control adjust latch	20
4	20D	20	200	1-8	Adjust latch spring	20
4	20D	20	200	1-9	Pedal spring	20
4	20D	20	200	1-10	Pedal mount bush	20
4	20D	20	200	1-21	Bearing bush	20
4	20D	20	200	1-22	Forward end piece	20
4	20D	20	200	2	Return spring
4	20D	20	200	4	Rudder cable guide	20
Elevator system
1	20D	20	300		Elevator system
2	20D	20	300	1	Control stick, general picture	20
3	20D	20	300	1-1	Control stick	20	100
3	20D	20	300	1-2	Torsion tube	20
4	20D	20	300	1-3	Adjustment spring
4	20D	20	300	1-4	Adjustment spring bearing
4	20D	20	300	1-9	Brake handle joint
3	20D	20	300	2	Trim system
4	20D	20	300	2-5	Lock spring
4	20D	20	300	2-6	Support bearing
4	20D	20	300	2-11	Trim knob
4	20D	20	300	3	Trim attitude plate
4	20D	20	300	6	Pushrod 1
4	20D	20	300	7	Control pulley attachment
3	20D	20	300	8	Pushrod guide
4	20D	20	300	9	Pushrod 2
4	20D	20	300	10	Pushrod 3
4	20D	20	300	11	Pushrod 11
3	20D	20	300	12	Elevator bellcrank
4	20D	20	300	12-2	Bellcrank centerpiece
4	20D	20	300	12-4	Balance leads
3	20D	20	300	13	Pushrod 5
4	20D	20	300	13-6	Express latch extension
4	20D	20	300	14	Spring
Wing flap system
2	20D	20	400		Wing flap control	04
4	20D	20	400	1	Mount bracket	04
1	20D	20	400	3	Attitude plate
3	20D	20	400	3-3	Doublers
4	20D	20	400	5	Handle
3	20D	20	400	6	Control lever	04
4	20D	20	400	6-8	Lock spring
4	20D	20	400	8	Guide
4	20D	20	400	9	Pushrod	04	20	100
0	20D	20	401		Wing flap mechanism	04
Airbrake system
2	20D	20	500		Airbrake control	04
2	20D	20	500	3	Control lever	04
4	20D	20	500	7	Pushrod	04	20
0	20D	20	501		Airbrake in RH wing
4	20D	20	501	2	Pushrod
4	20D	20	501	8	Lock lever	20
4	20D	20	501	10	Bearing bush	20
4	20D	20	501	16	Adjustment rod	20
3	20D	20	501	19	Lifting lever	20	40
4	20D	20	501	21	Bearing bush	20
4	20D	20	501	22	Strut	20	40
3	20D	20	501	23	Surface plate
2	20D	20	501	24	Brake plate	20	45
4	20D	20	501	24-6	Surface plate pin
4	20D	20	501	25	Surface plate spring
0	20D	20	502		Brake mechanism	04
Landing gear
1	20D	22	100		Landing gear	04
2	20D	22	100	1	Forward strut
3	20D	22	100	2	Lower aft strut
2	20D	22	100	3	Upper aft strut
2	20D	22	100	4	Torsion lever
3	20D	22	100	5	Shaft
4	20D	22	100	6	Bush
4	20D	22	100	9	Bearing bush
4	20D	22	100	13	Bearing bush
4	20D	22	100	17	Compression bush
4	20D	22	100	18	Shaft bush
4	20D	22	100	24	Trim spring	20
Tow coupling control
2	20D	21	200		Tow coupling control
3	20D	21	200	3	Coupling attachment plate	20
4	20D	21	200	4	Coupling cable attachment	20
4	20D	21	200	5	Coupling cable attachment	20
3	20D	21	200	26	Coupling assembly
Tail Wheel
4	20D	22	200		Tailwheel
4	20D	22	200	1	Tail Wheel shaft	20
4	20D	22	200	2	Tail Wheel bush
Landing gear system
2	20D	22	300		Operation of the landing gear
4	20D	22	300	1	Mount bracket	20
4	20D	22	300	2	Sliding tube	20
1	20D	22	300	3	Attitude plate
4	20D	22	300	3-2	Doubler
2	20D	22	300	3-3	Spring
3	20D	22	300	4	Landing gear actuator rod
4	20D	22	300	7	Guide
4	20D	22	300	8	Support
4	20D	22	300	9	Pushrod	20	30
Ballast system
0	20D	24	001		Ballast installation
3	20D	24	001	5	Ballast bag	90
4	20D	24	001	9	Support
4	20D	24	001	10	Mount plate
4	20D	24	001	11	Operation lever
Instrument system
1	20D	25	001		Instrument tubes
3	20D	25	001	1	Pitot tube and ventilation flap	04	40
4	20D	25	001	2	Static pressure probe
4	20D	25	001	3	Compensator joint
2	20D	25	002		Total energy compensation
0	20D	25	100		Instrument board
Construction General
1	20D	50	001		General view
2	20D	50	002		Water and pressure holes
Fuselage Construction
0	20D	51	100		Fuselage construction	40	60
3	20D	51	100	8	Forward main bulkhead
2	20D	51	100	8-2	Intermediate tube	40
1	20D	51	100	9	Wheel well
3	20D	51	100	10	Aft main bulkhead
3	20D	51	100	10-2	Suport rod
Fin construction
0	20D	52	100		Fin construction	66
2	20D	52	100	4-5	Horizontal stabilizers brackets Serial numbers 20667-: Horizontal stabilizer aft mount bracket
4	20D	52	100	8	Rudder upper bracket	20
3	20D	52	100	11	Rudder lower bracket	40
Rudder construction
1	20D	53	100		Rudder construction	40	66
4	20D	53	100	2	Upper hing pin
4	20D	52	100	6	Lower hinge pin
4	20D	52	100	7	Control brackets	20
4	20D	53	100	8	Stops	20
1	20D	53	101		Profile st 500
1	20D	53	102		Profile st 1000
Wing General
0	20D	54	001		Profile st 500
0	20D	54	002		Profile st 1465
0	20D	54	003		Profile st 2430
0	20D	54	004		Profile st 3395
1	20D	54	005		Profile st 4350
1	20D	54	006		Profile st 4530
1	20D	54	007		Profile st 5200
2	20D	54	008		Profile st 5950
2	20D	54	009		Profile st 6700
2	20D	54	010		Profile st 7435
0	20D	54	011		Brake box st.prof st 1850
0	20D	54	012		Root profile st 350
Wing Construction
0	20D	54	100		Wing construction	40
3	20D	54	100	5	Secondary spar
1	20D	54	100	13	Brake housing	20
2	20D	54	100	17, 27	Rear spar	20
4	20D	54	100	28	Aileron hinge and shaft	20
4	20D	54	100	29	Aileron hinge and shaft	20
4	20D	54	100	30	Aileron hinge and shaft	20
4	20D	54	100	34	Aileron hinge and shaft	20
4	20D	54	100	37	Aileron hinge and shaft
1	20D	54	200		Flange and web construction	20
1	20D	54	201		Root rib dimensions	20
Wing mount
1	20D	54	300		Wing mount	35
3	20D	54	300	3, 4	Safety pin components	20
3	20D	54	300	5-2	Main bolt bracket	20	40
3	20D	54	300	5-1, 6	Main bolt and bush	20
4	20D	54	300	7	Assembly bush	20
3	20D	54	300	9	Main bolts	20
1	20D	54	301		Wing mount	20
3	20D	54	301	9, 10	Wing mount components	20
Wing flap construction
1	20D	55	100		Wing flap construction	20			Same as in E model.
1	20D	55	100	3	Flap spar construction
4	20D	55	100	15	Aileron hinge
3	20D	55	100	17	Actuating bracket
4	20D	55	100	24	Shaft tube
Horizontal stabilizer construction
1	20D	58	100		Horizontal stabilizer construction	40	66
4	20D	58	100	1	Forward mount bracket	20
4	20D	58	100	10	Aft mount bracket
1	20D	58	101		Profile st 00
1	20D	58	102		Profile st 500
1	20D	58	103		Profile st 1000
Elevator construction
1	20D	59	100		Elevator construction	04	40	66
4	20D	59	100	3	Hinge pin
4	20D	59	100	6	Actuating bracket
Cockpit canopy
3	20D	60	100, 201	1-6, 1, 2, 3	Canopy metal components	20
1	20D	60	200		Canopy locking
3	20D	60	200, 201	1, 2	Canopy metal components	20
1	20D	60	201		Canopy jettisoning	04
4	20D	60	201	4	Locking plate
Seat
2	20D	62	001		Seat	04
3	20D	62	001	3	Headrest	30
3	20D	62	001	3-1	Headrest plate
4	20D	62	001	3-3	Bearing mount
3	20D	62	001	3-4	Fuselage plate
4	20D	62	001	3-6	Spring
3	20D	62	001	3-7	Adjusting rod
2	20D	62	001	5	Cable tube
4	20D	62	001	16	Cable guide
3	20D	62	001	18	Regulator slide	40
2	20D	62	001	19	Regulator body
4	20D	62	001	26	Pulley attachment
General
2	20D	93	001		Safety belt buckle	30	35
3	20D	10	001		Assembly tool	20
4	00	93	002		P.B.T.

Page was last updated