PIK-20E list of drawings

Drawings with an active link may be downloaded from this page as pdf files. Observe that the drawing opening from the link is not necessarily the same amendment as that marked in the list. This due to the fact that the amendment that has been noted in the list may not be found in Trafi’s archives. In this case the drawing has been replaced by its closest equivalent. Drawings that are not listed may be ordered from Traficom.

Size	Type	Chapter	Drawing n:o	P/n	Subject	Amendments			Add. information
						a	b	c
Control system general
0	20E	20	001		Control levers in center fuselage
0	20E	20	001	1	Lever attachmet	261
2	20E	20	001	1-15	Lift mechanism body	271
3	20E	20	001	1-18	Strut	265
3	20E	20	001	1-19	Strut	265
4	20E	20	001	1-17	Fastener
3	20E	20	001	2	Aileron bellcrank	204	220
3	20E	20	001	4	Aileron control lever	299	299
3	20E	20	001	5	Wing flap control lever	204	220
3	20E	20	001	6	Aileron rocker arm	239
3	20E	20	001	7, 8, 14	Movement rods	212
4	20E	20	001	7-1	Pushrod head
3	20E	20	001	9	Airbrake bellcrank
4	20E	20	001	11	Airbrake shaft	204
4	20E	20	001	12	Airbrake actuator bellckrank	204	220
3	20E	20	001	13	Airbrake control lever
4	20E	20	001	15	Bush	291
4	20E	20	001	16	Washer	220
4	20E	20	001	18	Bush	220
4	20E	20	001	19	Washer	220
4	20E	20	001	31	Wing flap control lever
3	20E	20	001	33	Wing flap torsion tube	215
4	20E	20	001		Shaft	220
4	20E	20	001	37	Bush	220
4	20E	20	001	38	Bush	220
4	20E	20	003		Pushrod head
4	20E	20	004		Pushrod head
4	20E	20	005		Breakaway joint
3	20E	20	006-8		Plastic components
4	20E	20	009		Rod end	320
Aileron control system
0	20E	20	100		Aileron control system
4	20E	20	100	1	Pushrod 1	283
4	20E	20	100	2	Aileron bellcrank	220
4	20E	20	100	3	Pushrod 2
4	20E	20	100	4	Pushrod 3
4	20E	20	100	5	Pushrod 4	265
3	20E	20	100	6	Aileron bellcrank	204	220	240
3	20E	20	100	6-1	Aileron bellcrank	204	220
4	20E	20	100	7	Pushrods 5, 7 ja 9
4	20E	20	100	8	Pushrod 6	265
4	20E	20	100	11	Pushrod 8	265
Rudder system
1	20E	20	200		Rudder system
1	20E	20	200	1	Rudder control
3	20E	20	200	1-2	Pedal	220
4	20E	20	200	1-3	Upper sliding tube	281
4	20E	20	200	1-4	Lower sliding tube	210
4	20E	20	200	1-5	Aft end piece	256
3	20E	20	200	1-6	Rudder control body	236
4	20E	20	200	1-7	Rudder control adjustment latch	220
4	20E	20	200	1-8	Adjustment latch spring	220
4	20E	20	200	1-9	Pedal spring	220
4	20E	20	200	1-10	Pedal mount bush	220
4	20E	20	200	1-21	Bearing bush	278
4	20E	20	200	1-22	Forward end piece	208	256
4	20E	20	200	2	Return spring
4	20E	20	200	4	Rudder cable guide	220
Elevator system
1	20E	20	300		Elevator system
1	20E	20	300	1	Control stick, general view	220
3	20E	20	300	1-1	Control stick	256	283
3	20E	20	300	1-2	Torsion tube
4	20E	20	300	1-3	Adjustment spring	283
4	20E	20	300	1-4	Adjustment spring bearing	286
4	20E	20	300	1-9	Brake handle joint
3	20E	20	300	2	Trim system	260
4	20E	20	300	2-5	Lock spring
4	20E	20	300	2-6	Support bearing	301
4	20E	20	300	2-11	Trim knob
4	20E	20	300	3	Trim attitude plate	306
4	20E	20	300	6	Pushrod 1
4	20E	20	300	7	Guiding pulley attachment
3	20E	20	300	8	Pushrod guide	274	287
4	20E	20	300	9	Pushrod 2
4	20E	20	300	10	Pushrod 3	265
4	20E	20	300	11	Pushrod 11
3	20E	20	300	12	Elevator bellcrank	294
4	20E	20	300	12-2	Bellcranks center piece
4	20E	20	300	12-4	Balance leads	294
3	20E	20	300	13	Pushrod 5	265
4	20E	20	300	13-6	Express latch extension
4	20E	20	300	14	Spring
Wing flap system
2	20E	20	400		Wing flap operation
4	20E	20	400	1	Mount bracket	311
1	20E	20	400	3	Attitude plate
3	20E	20	400	3-2	Doubler	300
4	20E	20	400	5	Handle
3	20E	20	400	6	Actuator rod	203	260	286
4	20E	20	400	6-8	Lock spring
4	20E	20	400	8	Guide
4	20E	20	400	9	Pushrod	204	220
3	20E	20	400	3-3	Adjustment plate starting with 20279	277
0	20E	20	401		Flap mechanism	204
Airbrake system
2	20E	20	500		Airbrake operation
2	20E	20	500	3	Actuator rod	203	258
4	20E	20	500	7	Pushrod	204	220
0	20E	20	501		Airbrake in RH wing	252
4	20E	20	501	2	Pushrod	265
4	20E	20	501	8	Lock arm	305
4	20E	20	501	10	Bearing bush	280	298	305
4	20E	20	501	15	Tube bush	305
4	20E	20	501	16	Adjustment arm
3	20E	20	501	19	Lifting arm	254	280	258
4	20E	20	501	21	Bearing bush	276	311
3	20E	20	501	22	Support lever	280	252	305
3	20E	20	501	23	Surface plate
1	20E	20	501	24	Brake plate	252	252	252
4	20E	20	501	24-6	Brake plate pin	225
4	20E	20	501	25	Brake plate spring	225
4	20E	20	501	26	Bearing bush starting with 20252	278	305
0	20E	20	501		Brake mechanism
Tow latch operation
2	20E	21	200		Tow latch operation	221
3	20E	21	200	3	Latch attachment English	221			Original revision
3	20E	21	200	26	Latch assembly	221
4	20E	21	200	4	Latch cable fastener	291
Landing gear
1	20E	22	100		Landing gear feathered	221
2	20E	22	100	1	Forward strut	268
3	20E	22	100	2	Rear strut lower
2	20E	22	100	3	Rear strut upper	221	281
2	20E	22	100	4	Torsion arm	282
3	20E	22	100	5	Shaft	262
4	20E	22	100	6	Bush
4	20E	22	100	9	Bearing bush
4	20E	22	100	13	Bearing bush
4	20E	22	100	17	Compression bush
4	20E	22	100	18	Shaft tube	276
4	20E	22	100	24	Trim spring	220
2	20E	22	100	3-2	Aft strut, componenets
4	20E	22	100	31	Aft strut, sliding	287
4	20E	22	100	38	Brake bush
Tail gear
2	20E	22	200		Tail gear	230	239
4	20E	22	200	1	Tail wheel
4	20E	22	200	2	Tail Wheel fork	206	230	272
4	20E	22	200	2-3	Bush	257	272
3	20E	22	200	3	Tail spring
4	20E	22	200	4	Tail spring attachment	230
4	20E	22	200	5	Guiding spring
4	20E	22	200	7	Flange bush	203	230
4	20E	22	200	8	Flange bush removed from 230	203
4	20E	22	200	9	Bearing bush
4	20E	22	200	10	Bush
4	20E	22	200	11	Shaft
4	20E	22	200	14	Guide spring attachment	230
4	20E	22	200	33	Bush	272
4	20E	22	200	38	Locking pin
Landin gear system
4	20E	24	001	11	Actuator arm
2	20E	22	300		Landing gear operation	221
4	20E	22	300	1	Attachment bracket	356
4	20E	22	300	2	Sliding tube	285
1	20E	22	300	3	Attitude plate	221
4	20E	22	300	3-2	Doubler	221
3	20E	22	300	3-3	Spring	296
3	20E	22	300	4	Landing gear operating shaft	203	260
4	20E	22	300	7	Guide
4	20E	22	300	8	Support	298
4	20E	22	300	9	Pushrod	220	230
Ballast system
0	20E	24	001		Ballast installation
3	20E	24	001	5	Ballast bag	247
4	20E	24	001	6	Support
4	20E	24	001	10	Attachment plate	290
Instrument system
1	20E	25	001		Instrument tubes
3	20E	25	001	1	Pitot tube and ventilation flap	275
4	20E	25	001	2	Static pressure sensor
4	20E	25	001	3	Compensation joint	281
2	20E	25	002		Total energy compensator
1	20E	25	003		Stall warning
3	20E	25	003	1	Sensor assembly
4	20E	25	003	8	Bracket
4	20E	25	003	1-2	Screw
1	20E	25	004		Stall warning system
4	20E	25	004	2	Bracket
4	20E	25	004	11	Attachment plate
2	20E	25	100		Instrument board
3	20E	25	100	1	Instrument side plate	276
3	20E	26	100		Antenna assembly
4	20E	26	100	1	Antenna components
4	20E	26	100	2	Antenna components
Electrical system
3	20E	28	001		Electrical system	219	228	250
3	20E	28	001	1	Ignition coils attachment	266, 294
4	20E	28	001	2	Washer
2	20E	28	001	3	Microswitch cover
2	20E	28	002		Electrical system for double ignition starting with 20294
Fuel system
1	20E	31	001		Fuel system	221	262, 264
1	20E	31	001		Fuel tank	265
4	20E	31	001	43	Clamp (feed fuel)
4	20E	31	001	44	Clamp (return fuel)
3	20E	31	001	1-1	Fueling opening tube
3	20E	31	001	1-1	Fueling opening tube
Construction General
1	20E	50	001		General picture
1	20E	50	002		Drainage and pressure holes
Fuselage construction
0	20E	51	100		Fuselage construction	221
3	20E	51	100	8	Forward main bulkhead
2	20E	51	100	8-2	Intermediate tube	223	258
1	20E	51	100	9	Wheel well	221
0	20E	51	100	10	Construction of aft main bulkhead (single page pdf), (multipage pdf)	252
3	20E	51	100	10-1	Seaming of aft main bulkhead
1	20E	51	100	32	Engine cowlings
1	20E	51	100	33	Minor fuselage components
1	20E	51	100	34	Wing and fuselage components
1	20E	51	100	35	Fuselage plywood supports
1	20E	51	100	36	Fuselage plywood components
Fin construction
0	20E	52	100		Fin construction
4	20E	52	100		Fin upper hinge	257	306
3	20E	52	100		Fin lower hinge
4	20E	52	100	4-(1,2)	Attachment pin	290	309
3	20E	52	100	5	Horizontal stabilizer forward attachment
4	20E	52	100	5-1	Horizontal stabilizer forward attachment components
4	20E	52	100	5-(2,4,5)	Horizontal stabilizer forward attachment components
4	20E	52	100	5-(6,7,8)	Horizontal stabilizer forward attachment components
4	20E	52	100	5-9	Horizontal stabilizer forward attachment components
3	20E	52	100	5-(1,9)	Horizontal stabilizer forward attachment
1	20E	52	100	24	Fin plywood components
1	20E	52	100	25	Wing flap, aileron, fin and rudder components
3	20E	52	100	4	Horizontal stabilizer aft attachment bracket
Fin construction
1	20E	53	100		Fin construction
4	20E	53	100	2	Upper hinge pin	301
4	20E	53	100	6	Lower hinge pin
4	20E	53	100	7	Actuator brackets	293
4	20E	53	100	8	Fin stop	220
1	20D	53	101		Profile st 500
1	20D	53	102		Profile st 1000
Wing General
0	20D	54	001		Profile st 500
0	20D	54	002		Profile st 1465
0	20D	54	003		Profile st 2430
0	20D	54	004		Profile st 3395
1	20D	54	005		Profile st 4350
1	20D	54	006		Profile st 4530
1	20D	54	007		Profile st 5200
2	20D	54	008		Profile st 5950
2	20D	54	009		Profile st 6700
2	20D	54	010		Profile st 7435
0	20D	54	011		Brake casing inst.prof st 1850
0	20D	54	012		Root profile st 350
Wing construction
0	20E	54	100		Wing construction	252
3	20E	54	100	5	Secondary spar
1	20E	54	100	13	Brake casing	252	305
2	20E	54	100	17,27	Rear spar
4	20E	54	100	28	Aileron hinge and shaft/a-version not in use	263	281
4	20E	54	100	29	Aileron hinge and shaft/a-version not in use	263	281
4	20E	54	100	30	Aileron hinge and shaft/a-version not in use	263	281
4	20E	54	100	34	Aileron hinge and shaft/a-version not in use	263	281
4	20E	54	100	37	Aileron hinge and shaft/a-version not in use	276
4	20E	54	100	40	Tip wheel shaft
1	20E	54	200		Construction of flange and web
1	20E	54	201		Root rib dimensions
1	20E	54	201	1	Root rib construction
Wing mount
1	20E	54	300		Wing mount
3	20E	54	300	3,4	Safety pin components	220
3	20E	54	300	5-2	Main bolt bracket	279
3	20E	54	300	5-1,6	Main bolt and bush	220
1	20E	54	300	7	Root web plate
3	20E	54	300	9,10	Wing mount components	220
3	20E	54	300	13	Main bolts	220
1	20E	54	301		Wing mount
4	20E	54	301	12	Assembly bush
0	20E	54	302		Instrument drawing
0	20E	54	303		Instrument drawing
0	20E	54	304		Instrument drawing
Wing flap construction
1	20E	55	100		Wing flap construction
1	20E	55	100	3	Wing flap spar construction
4	20E	55	100	15	Aileron hinge	266
3	20E	55	100	17	Actuator bracket	281
4	20E	55	100	24	Shaft tube	254
1	20E	55	100	1	Root flap construction	296
1	20E	55	100	2	Aileron construction	296
3	20E	55	100	3	Operation arcs
4	20E	55	100	4	Bush
Horizontal stabilizer construction
1	20E	58	100		Horizontal stabilizer construction	221
4	20E	58	100	1	Forward attachment bracket
4	20E	58	100	10	Aft attachment bush
4	20E	58	100	13	Elevator hinge starting with 20246
4	20E	58	100	14	Bush	272
1	20E	58	101		Profile st 00
1	20E	58	102		Profile st 500
1	20E	58	103		Profile st 1000
Elevator construction
1	20E	59	100		Elevator construction	221
4	20E	59	100	3	Hinge pin	221	291
4	20E	59	100	6	Actuator bracket
1	20E	59	100	14	Horizontal stabilizer, elevator and rudder plywood components
Cockpit canopy
2	20E	60	200		Cockpit canopy	253
2	20E	60	200	1	Canopy ring
3	20E	60	200	6	Small hatch guides
3	20E	60	200	9	Support plate	214	273
3	20E	60	200	10	Hinge
4	20E	60	200	11	Intermediate tube
4	20E	60	200	12	Shaft
4	20E	60	200	13	Bush	284
2	20E	60	200	14	Lifting arm	231	253
3	20E	60	200	15	Plate	283
4	20E	60	200	16	Lock pin	279
4	20E	60	200	17	Torsion arm	203	220	304
4	20E	60	200	18	Actuating rod
4	20E	60	200	19	Knob
4	20E	60	200	20-1	Bracket	310
3	20E	60	200	20	Canopy locking	271
4	20E	60	200	20-2	Lock arm	210	271
4	20E	60	200	22,23	Bush
4	20E	60	200	20-(3,4)	Locking rod	210
4	20E	60	200	20-7	Bush	264
4	20E	60	200	20-5	Handle	255
4	20E	60	200	20-6	Rivet bushes	210
4	20E	60	200	21	Guide
4	20E	60	200	37	Gas spring attachment bush	347
2	20E	60	200	37	Barbed wire protection
4	20E	60	200	39	Attachment bracket for rearview mirror
4	20E	60	200	20-9	Locking rod retainer	280
3	20E	60	200	14-7	Bracket will be removed 252
1	20E	60	201		Cockpit signs
Seat
2	20E	62	001		Seat
3	20E	62	001	3	Headrest, will be removed starting with 257	230	257
3	20E	62	001	3-1	Headrest plate, will be removed starting with 257	257
4	20E	62	001	3-3	Bearing mount, will be removed starting with 257	257
3	20E	62	001	3-4	Fuselage plate, will be removed starting with 257	257
4	20E	62	001	3-6	Spring, will be removed starting with 257	257
3	20E	62	001	3-7	Adjustemnt rod, will be removed starting with 257	257
2	20E	62	001	5	Cable tube
4	20E	62	001	16	Cable guide
3	20E	62	001	18	Adjuster slide	240
2	20E	62	001	19	Adjuster body
4	20E	62	001	20	Safety belt mating bolt
0	20E	80	001		Engine
Pull cable
1	20E	80	002		Cable mechanism	217
4	20E	80	002	2	Cable tube	208	217	306
3	20E	80	002	4	Return spring
4	20E	80	002	6	Pull cable bracket	250
4	20E	80	002	19	Spring attachment piece
4	20E	80	002	23	Pull cable bush	306
Door operating mechanism
1	20E	80	100	1	Engine doors
1	20E	80	100		Door operating mechanism
3	20E	80	100	3	Lever shaft	213	273	278
4	20E	80	100	4	Pushrod	210	264
4	20E	80	100	5	Bracket	214
4	20E	80	100	6	Shaft support	261
4	20E	80	100	7	Bush
4	20E	80	100	11	Cable clamp
4	20E	80	100	23	Small hatch clamshell
4	20E	80	100	24	Bracket
4	20E	80	100	25	Spring
1	20E	80	102		Engine shields
1	20E	80	102	1	Airflow plate	295
2	20E	80	102	2	Airflow plate	294
2	20E	80	102	3	Coil housing	294			Original revision
1	20E	80	102	4	Airflow plate	296
2	20E	80	102	5	Carburettor housing plate
1	20E	80	102	6	Carburettor housing
4	20E	80	102	7	Bracket
4	20E	80	102	8	Bracket
4	20E	80	102	9	Bush
4	20E	80	102	10	Wire clamp
Operating mechanism for lower lock
1	20E	80	400		Operating mechanism for lower lock	280
4	20E	80	400	3	Lower lock hinge	214	269	320
4	20E	80	400	4	Lower lock clamshell	269	352
4	20E	80	400	5	Nut
Engine lifting mechanism
1	20E	80	500		Engine lift mechanism	261
2	20E	80	500	1	Crank mechanism	261
3	20E	80	500	1-1	Fuselage plate	210	259	272
3	20E	80	500	1-2	Hand crank
3	20E	80	500	1-2-1	Hand crank body
4	20E	80	500	1-2-1-4	Grooved bush
4	20E	80	500	1-2-1-5	Perforated plate
3	20E	80	500	1-3	Door crank	209	261
4	20E	80	500	1-4	Crank knob
4	20E	80	500	1-5	Chain wheel
3	20E	80	500	1-6	Housing	254
4	20E	80	500	1-7	Bush	254	280
4	20E	80	500	1-8	Bush	276	276
4	20E	80	500	1-9	Crank shaft
4	20E	80	500	1-13	Bush	206	286
3	20E	80	500	1-16	Stop plate	203	251
4	20E	80	500	1-17	Bush
4	20E	80	500	1-19	Spring plate	261	261
4	20E	80	500	1-21	Lock pin
4	20E	80	500	1-22	Stop	265
4	20E	80	500	1-24	Bush	316	310
4	20E	80	500	5	Chain tightener
4	20E	80	500	6	Chain lock	209	305
4	20E	80	500	9	Tube clamp
5	20E	80	500	11	Shaft	261
4	20E	80	500	12	Gear wheel
5	20E	80	500	13	Bearing mount, will be removed starting with 260	205
3	20E	80	500	14	Support plate, will be removed starting with 261
4	20E	80	500	15	Bearing bush, will be removed starting with 250
4	20E	80	500	16	Bearing bush, will be removed starting with 250	278
4	20E	80	500	17	Bearing bush, will be removed starting with 250	271	277
4	20E	80	500	18,19	Bearing retaining plate	271
4	20E	80	500	20	Bearing shaft	297
3	20E	80	500	26	Rack	284
4	20E	80	500	27	Bush
4	20E	80	500	32	Stab. upper bush	254
3	20E	80	500	34	Fastening piece
3	20E	80	500	35	Support	231
4	20E	80	500	1-(5, 9)	Chain wheel and crank shaft
4	20E	80	500	40	Bearing bush starting with 20261
3	20E	80	500	39	Shaft tube
4	20E	80	500	1-2-1	Hand crank handle
4	20E	80	500	1-2-5	Hand crank latch
4	20E	80	500	1-2-3	Bush
4	20E	80	500	1-2-2	Hand crank knob
4	20E	80	500	1-2-4	Spring
Reduction gear
1	20E	81	100		Reduction gear	252
1	20E	81	100	2	Propeller mount	214
3	20E	81	100	3	Gear belt wheel	214	252	332
3	20E	81	100	4	Gear belt wheel	214	252	332
4	20E	81	100	9	Bearing cover, removed starting with 251
4	20E	81	100	10	Shaft nut
4	20E	81	100	13	Mating ring
4	20E	81	100	15	Forward plate	210	315
4	20E	81	100	17	Propeller spacer
4	20E	81	100	18	Bush	252	257
4	20E	81	100	20	Washer
4	20E	81	100	21	Beltwheel flange plate forward
4	20E	81	100	23	Beltwheel flange plate aft	268
4	20E	81	100	25	Stud	259	286
4	20E	81	100	26	Stud	261	285
3	20E	81	100	2-1	Propeller shaft	203
4	20E	81	100	29	Starter motor attaching piece	214	219
4	20E	81	100	2-2	Propeller mount attaching bush	250
4	20E	81	100	2-3	Propeller mount attaching bush	250
4	20E	81	100	12	Bearing seal plate	252
Halfcompressor
1	20E	82	001		Halfcompressor
3	20E	82	001	2	Button shaft	261	290
4	20E	82	001	3	Bracket	247
4	20E	82	001	4	Bracket	247
4	20E	82	001	5	Shaft
4	20E	82	001	6	Overflow tube	259	309
4	20E	82	001	8	Bracket	309
4	20E	82	001	9	Spring
4	20E	82	001	11	Cable clamp
4	20E	82	001	19	Half compressor valve sealing bush
Carburettor and choke
1	20E	82	100		Carburettor and choke
3	20E	82	100	3	Carburettor lever body	205	268
4	20E	82	100	4	Carburettor lever
4	20E	82	100	5	Carburettor lever bush
4	20E	82	100	6	Lock pin	278
1	20E	82	100	7	Carburettor housing
4	20E	82	100	8	Guide	208	259
4	20E	82	100	9	Cable end piece	256
4	20E	82	100	10	Tightening wheel
4	20E	82	100	11	Cable lamp
4	20E	82	100	12	Lever bush	277
4	20E	82	100	16	Lock pin	278
4	20E	82	100	34	Choke cable bracket	277
4	20E	82	100	11-(1,2,3)	Cable clamp components
4	20E	82	100	37	Fastener
Engine support
1	20E	82	200		Engine support
1	20E	82	200	1	Pylon	244
3	20E	82	200	2	Pylon hinge	301
4	20E	82	200	3	Bush	305
4	20E	82	200	4	Cylinder cover plate	255	281
4	20E	82	200	5	Rubber cushion bush
4	20E	82	200	6	Stud	275
4	20E	82	200	15	Bush	205
Muffler
1	20E	84	100		Muffler attachment	211
4	20E	84	100	5	Bush
4	20E	84	100	4	Washer
4	20E	84	100	6, 7	Rubber cushion
4	20E	84	100	8	Fiber cushions
Propeller brake
1	20E	87	001		Propeller brake	250
4	20E	87	001	3	Lever extension	301
4	20E	87	001	4	Pin
4	20E	87	001	5	Endpiece attachment	288	288
4	20E	87	001	6	Endpiece attachment	206	250
3	20E	87	001	7	Brake lever
4	20E	87	001	8	Brake pad
4	20E	87	001	9	Return spring
4	20E	87	001	10	Bush	287
4	20E	87	001	11	Bush
4	20E	87	001	12	Brake bracket
4	20E	87	001	13	Cable clamp
General
3	20E	10	001		Assembly tool
1	20E	70	001		Propeller
1	20E	60	001		Canopy hinging
4	20E	93	100		Nicopress tool

Page was last updated